Star ProductsMedium and High Voltage SwitchgearLow Voltage SwitchgearSubstationsPower Distribution BoxesAuthorized CabinetsPhotovoltaic CabinetsGas-Insulated CabinetsBuswaysComprehensive Training Building (EPC) ProjectEPC Engineering of Du'an People HospitalEPC Project of Teng County Industrial Park40.008MWp Distributed Photovoltaic ProjectPower Engineering General ContractingBYD's Phase III Power Distribution ProjectNanning Qingxiu Tesla Center Power DistributionGaoshan Operation Area Power Distribution ProjectGuida Paper 35kV Substation EngineeringIron & Steel Base Power Distribution Project10kV Power Distribution Project for Cold StorageIndustryBeitou Yinshan Power Distribution ProjectPower Distribution Project of Hezhou Binfen MallLiuzhou CR Land Power Distribution ProjectGuangxi MYJ Industry Power Distribution ProjectPower Distribution Project of Creative ParkCommercial Real EstateIndustry - Education Integration Power SupplyYao Medicine Hospital Power Distribution ProjectMuseum Power Distribution ProjectSurveying & Mapping Bureau. Power Distribution ProIntegration Training Building Power DistributionGX Agricultural Vocational and Technical UniversitNanning University Training Building Power DistribGX Agricultural Engineering Vocational and TechnicPujin Road Phase II Sewage Pipe Box-type SubstatioInfrastructureBaise Sports Center Charging Piles Power DistributNapo People's Court Charging Piles Power DistributSmart Park Charging Piles Power Distribution ProjeEnergy and PowerPower Distribution Project of Nanning Rail TransitTian'e-Beihai Highway Power Distribution ProjectGuanyang - Pingle Mechanical & Electrical EngineerTransportation1.92MW Distributed Photovoltaic Power ProjectPhotovoltaic Power Generation Project (Phase I)Agriculture, Forestry, Animal Husbandry & FisheryProjects OverviewNews CenterVideo UpdatesIndustry FAQIndustry White PaperGroup ProfileIndustrial Products Platform QiansimaiHonors and QualificationsSeeking Overseas Distributors
Share to:

SWDFW-12 Outdoor Switchgear (Cable Distribution Box)

A switchgear is used to take a single power supply from a sub - station and distribute the electricity to several areas or different buildings in need of power through multiple switch cabinets installed in the “switchgear”. The voltage remains unchanged. Figuratively speaking, it “divides” a single power supply into multiple power supplies.
It uses pre - fabricated live - touchable silicone rubber cable heads, which are fully sealed, fully insulated and maintenance - free, reliably ensuring personal safety. It has a compact structure, a small and beautiful appearance, and a stainless - steel double - layer box, with a service life of more than twenty years.
Product Description
Specification

1. Features

It uses prefabricated live touchable silicone rubber cable heads, which are fully sealed, fully insulated, and maintenance-free, which can reliably ensure personal safety. It has a compact structure, a small and beautiful appearance, and a stainless steel double-layer box with a service life of more than 20 years.

Without affecting the operation of the main grid, regional power outages and maintenance can be carried out to reduce the scope of the outage.

It can be equipped with one or more SF6 load switches. The wiring methods are flexible and diverse, and the branch line can reach up to 8 circuits.

Optional lightning arresters, short-circuit fault indicators, current-limiting fuses, etc. can meet various user requirements.


2. Scope of Application

It is widely used in urban power grid transformation, residential areas, commercial centers and other densely populated areas.


3. Usage conditions and environment

The altitude does not exceed 2500m.

Ambient temperature: -45℃-+45℃.

Relative humidity: daily average value not exceeding 95%, monthly average value not exceeding 90%.

Installation location: A location without fire, explosion hazards, conductive dust, chemical corrosive gases and severe vibrations. If the above conditions are exceeded, the user can negotiate with our company.


4. Commonly used cable connectors

Made of imported high-quality insulating rubber through fully automated injection molding, the inner and outer layers are both semiconducting shields. The inner layer balances the internal electric field, while the outer shield is grounded to maintain zero potential on the cable head surface. The inner layer at the lower end of the stress cone is in close contact with the cable's semiconducting layer, while the outer semiconducting layer is in close contact with the outer semiconducting layer of the cable head and is grounded through the cable head's grounding hole. This not only eliminates the problem of electric field concentration at the cutoff point of the cable's outer shield, but also maintains zero potential on the cable's outer shield, ensuring personal safety.

The front connector of the touchable cable is directly installed on the equipment casing, and can then be connected to the rear connector of the touchable cable to form multiple outgoing lines. It can also be connected to the lightning arrester to provide overvoltage protection for the power grid.

Made of imported high-quality insulating rubber through fully automated injection molding, the inner and outer layers are both semiconducting shields. The inner layer balances the internal electric field, while the outer shield is grounded to maintain zero potential on the cable head surface. The inner layer at the lower end of the stress cone is in close contact with the cable's semiconducting layer, while the outer semiconducting layer is in close contact with the outer semiconducting layer of the cable head and is grounded through the cable head's grounding hole. This not only eliminates the problem of electric field concentration at the cutoff point of the cable's outer shield, but also maintains zero potential on the cable's outer shield, ensuring personal safety.

The touchable cable rear connector is installed on the touchable cable front connector through a connector. Its rear end can be connected to another rear connector through a connector to form multiple outgoing lines. It can also be connected to a voltage avoider to provide overvoltage protection for the power grid.



Technical Parameters


Serial numbernameparameterSerial numbernameparameter
1 Rated voltage12KV7 Rated short-time withstand current25kA/4S
2 Rated current630A8 Rated peak withstand current50kA
3 Power frequency withstand voltage (phase to ground)42kV/min9 Rated breaking capacitance current45A
4 Lightning impulse voltage75KV10 Rated breaking inductance current16A
5 Rated breaking current630A11 Full load breaking times>100
6 Rated short-circuit breaking current (peak value)50kA12 Number of mechanical operations of opening and closing2000